Prototyping Tools

Add to compare
up to 4 items

Displaying 1 to 11 (of 11 products)

Product Image	Quantity-	Item Name	Price
Add to compare	2	Base Workshop Kit KIT with all the parts to partecipate to an Arduino Workshop Base Level is made of: 1 USB cable 1 Straight single line pinhead connectors 2,54 40x1 1 Breadboard, 840 tie points 1 Set of 70 breadboard jumper wires 5 10K Ohm Resistors 1/4W 5 2.2K Ohm Resistor 1/4 W 10 220 Ohm Resistors 1/4W 5 330K Ohm Resistors 1/4W 5 100nF capacitor polyester 5 10nF capacitor polyester 3 100uF electrolytic...	Contact Us
Add to compare	13	Breadboard with Wire Kit 840 points Plastic Breadboard for rapid prototyping and 70 wire kit	Contact Us
Add to compare	28	Jumper F/F - 15cm 10pz These are 155mm long jumpers with female connectors on both ends. Use these to jumper from any male header on any board, to any other male header. Multiple jumpers can be installed next to one another on a 0.1" header. Comes as 1 package of ten jumpers (colors shown).	Contact Us
Add to compare	39	Jumper M/M - 15cm 10pz These are 155mm long jumpers with male connectors on both ends. Use these to jumper from any female header on any board, to any other female header. Multiple jumpers can be installed next to one another on a 0.1" header. Comes as 1 package of ten jumpers (colors shown).	Contact Us
Add to compare	2	IC Hook with Pigtail These are good quality IC test hooks with a male connection wire. Instead of a single hook, these have two hooks that are capable of grabbing very small points (like SOIC IC legs). Comes in a bag of five IC hooks of different colors (black, red, white, blue, and green). We use them with the Bus Pirate logic analyzer harnesses but are very cool on their own. Wire length is 2.5" long. Male pin...	Contact Us
Add to compare	1	Alligator Test Leads - Multicolored 10 Pack Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether you're just trying to make a few quick connections to test your circuit or having trouble making your multimeter leads stay where you need them, these spring-loaded clips are a workshop must-have. Each lead in this pack of tern is 50cm long with a...	Contact Us
Add to compare	128	15mm Strip 6 and 8 ways Pair of 1 8ways and 1 6ways Female/Male strip, very useful to be used for Arduino boards extensions. Dimensions: plastic body 8.5mm - pins 15mm - total 23.5mm.	Contact Us
Add to compare	13	15mm Strip 6, 8 and 10 ways (for Rev3 platforms) 2x 8ways1x 6ways1x 10ways Female/Male strips, very useful to be used for Arduino Rev3 boards extensions. Dimensions: plastic body 8.5mm - pins 15mm - total 23.5mm.	Contact Us
Add to compare	0	Fingerprint Scanner - TTL (GT-511C3) Fingerprint scanners are awesome. Why use a key when you have one right at the tip of your finger? Unfortunately, they're usually unreliable or difficult to implement. Well not anymore! We've found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you can easily embed it into your next project. The module itself does all of the heavy lifting behind reading and...	Contact Us
Add to compare	1	Breadboard Power Supply Stick 5V/3.3V This is a very simple board that takes a 6-12V input voltage and outputs a selectable 5V or 3.3V regulated voltage. All headers are 0.1" pitch for simple insertion into a breadboard. Input power can be supplied to either the DC barrel jack or the two pin header labeled + and -. Output power is supplied to the pins labeled GND and VCC. Board has both an On/Off switch and a voltage select...	Contact Us
Add to compare	7	Gas Sensor Breakout Board Simple breakout board for the MQ - 3, MQ - 4, MQ - 6 and MQ - 7 gas sensors. All you need is VCC at 5V, GND, and a resistor to an ADC, that is it. Note: This is the PCB only. Sensors listed are not included and sold separately. Documents: SchematicEagle FilesWiring Example	Contact Us

Displaying 1 to 11 (of 11 products)

Information

Search